Acquiring a motorcycle stand is sometimes inconvenient to repair and maintain your bike.
At times, not all motorcycle stands are easy to use and repair your bike.
The good news is there are countless hacks to make DIY motorcycle stands. These DIY motorcycle stands require the minimal burden of buying a motorcycle stand. Or searching for the right lift jack.
Making a DIY motorcycle stand only requires a few materials with easy instructions to make a simple motorcycle stand. You can construct a homemade dirt bike stand without any hassle.
How to Put Motorcycle on a Stand | DIY Motorcycle Stands
Before you begin to know how to make a motorcycle stand, there are different ways to put a dirt bike on a stand. This will allow you to find out how to make a DIY motorcycle stand. Such methods are mentioned below:
Lift Stand
A lift stand is the easiest method to put your dirt bike on and do all the work. This motorcycle stand requires no effort at all!
All you have to do is move your bike over to the stand and place it in a proper position. Use the lift to repair your motorcycle.
The lift stand will do the rest, and you do not have to worry about bending over or suffering other injuries. You can repair your motorcycle without acquiring any tedious procedures!
Side Panel Lift – Motorcycle Stand DIY
A side panel lift is the most popular method of lifting the dirt bike onto the stand. This method has been around for a long time and has been used by many riders to lift their bikes onto the stand. Many workshops rely on a side panel lift to lift the motorcycle for ease of maintenance.
If you prefer an old-fashioned way of repairing your bike, this method is right for you! To do this you need to lean your bike to the side. Use your arms and hips for support to lift the bike and place it onto the stand. You can repair your bike without straining your back and shoulders! This makes a suitable motorcycle stand DIY.
Rear Tyre Lift
The rear tyre lift is the same as the side panel lift; the only difference is the method works by lifting the rear tyre onto the motorcycle work stand.
To do this method is to carefully grab the rear tyre with your dominant hand and the rear fender with your left hand. Lift and slowly move the bike over to the stand and centre the front. Be careful with the front tyre as the front tyre might slip during the lifting process when placing the bike onto the stand. This will cause fatal injuries!
Triangle Stand
The triangle stand is the easiest way of repairing the bike as it eliminates the need for lifting the bike!
To use this method is to place the triangle stand carefully with the side of the rear tyre and repair your bike. The good thing about this stand that it is cheap and requires no expensive tools at all! The triangle stand is stable and is easy to reach.
Nose Wheelie
A nose wheelie is one of those methods where riders love to roll their bikes onto the stand. This technique works well if you want to show your coolness. Doing wheelies will help you to put your bike onto the stand. This technique is simple, all you have to do is to ride and place your bike on its stand.
Rear Wheelie
A rear wheelie is a fancier way of repairing the motorcycle. This method requires several practices to become an expert on putting the bike onto the stand. The easy way to do a rear wheelie is to roll your bike manually and do not forget to turn off the engine. Use the front brakes and the rear wheel will rise. To do this method is to have a kill switch to keep your dirt bike secure.
How to Build a Motorcycle Stand – How to Make a Motorcycle Stand – DIY Motorbike Stand
Many riders make DIY motorcycle stands to fix and repair their bikes. These self-made stands will help you to save time and money from maintaining your bike at the workshop. If you want to build a DIY motorcycle center stand. There are endless DIY motorcycle stands to check out.
Here, I will give you easy instructions on building a wooden stand. For this hack, you need:
- 1 x 2 inches wood (2 pieces)
- 10 x 20 inches base wood
- 18-inch long conduit
- 5/16 x 4-inch bolt
- A few bolts for securing the conduit to the wood pieces
- A screw for one upright
- A hammer
- A driller
Method:
- To know how to build a motorcycle stand is to bend the conduit by hammering both ends. To do this step, lay the conduit tube on an anvil. Secure the flattened end in a vice and bend to the proper angle.
Note: this step involves trial and error, and you have to take several tries to bend according to your desired angle and the size of your bike. - Use the basewood and measure the dimensions of your bike. Use the two long pieces of wood and cut the wood to the correct size depending on the size and style of your bike.
- Drill 7/16 inch holes in the upright wood at the correct position for your bike. Assemble the parts by joining the 18-inch conduit by using bolts and screws. Use a small clamp and join the other end of the stand with smaller nuts. Use a 1/8-inch bolt for easy insertion when securing the bike.
- Your wooden bike stand is ready to repair your motorcycle!
- If making a wooden stand is inconvenient for you, there is other instruction of DIY motorcycle stands of building a portable bike rear stand using metal pipes. To make this stand, click on the link.
How to Use DIY Motorcycle Stands – How to Put a Motorcycle on a Stand
Many motorcycles are equipped with side stands or kickstands to support the motorcycle when parked in the parking lot. This type of stand is familiar to any rider that has ever owned a motorcycle.
Some motorcycles are equipped with a center stand that extends from under the bike and lifts the rear wheel. This type of stand makes it easier to repair the rear wheel but lacks the stability of the side stand.
If using DIY motorcycle stands is inconvenient, there is a detailed guide on how to use a motorcycle front and rear stand.
So, how do you use a motorcycle front stand? If carried out carefully, the procedures mentioned below:
- When using motorcycle stands, make sure you begin repairing them by installing the rear stand. The front stands should never be used without the rear stand in place, as this would cause the bike to topple over.
- Rear stands lift the bike from the swing arm using various styles. The most common style that lifts the bike is to use small spools that mount to each side of the swingarm.
- Simply support the bike in a vertical position by positioning the stamp to the rear of the bike and positioning the clips of the stand at the spools.
- Once the bike is secured and ready to lift, press down the handle and lift the bike slowly. The handle should be lowered to the ground, and the bike will support it.
- Note: do be careful when moving the bike while on the stand. Depending on the style of the stand, you can push or pull the bike without creating issues. To be on the safe side, remove the stand before moving the bike.
- To install the front stand, there are two ways to lift the bike by lifting under the steering head or by lifting from the bottom of the forks.
- To lift under the steering head, position the pin of the stand under the steering head and insert the pin. Secure the pin before you begin to lift the bike.
- Once the pin is in place, press down on the handle to lift the front.
- To lift from under the forks, position the front stand in the center of the front wheel and place the small rubber-coated swivels under the forks.
- Note: make sure that the lower swivel is under the center of each fork and not on the edge. You do not want the fork to slip off!
- Slowly press down the handle to lift the front. The stand handle should be lowered to the ground.
- The rear and front stands are ready to repair the bike.
Conclusion
Here are the simple guides for DIY motorcycle stands! You can see these guides will help you to save time and money from repairing your bike at the workshop.
Since motorcycle stands are inconvenient to fix their bikes. Riders use DIY motorcycle stands to repair their bikes at home. To make a DIY motorcycle stand at home, grab some materials and construct the stand using the above instructions. Then, you will begin repairing your bike at your convenience.
So, choose any DIY motorcycle stands and start repairing your bike!
You can also read how to hotwire a motorcycle and shorty levers.